this post was submitted on 09 Nov 2026
11 points (100.0% liked)

Do It Yourself

9000 readers
35 users here now

Make it, Fix it, Renovate it, Rehabilitate it - as long as you’ve done some part of it yourself, share!

Especially for gardening related or specific do-it-yourself projects, see also the Nature and Gardening community. For more creative-minded projects, see also the Creative community.


This community's icon was made by Aaron Schneider, under the CC-BY-NC-SA 4.0 license.

founded 3 years ago
MODERATORS
 

The rental I'm in came with my shower being covered in mold 💀 I've worked to clean a lot of it out but ofc it's in the railings

I want to do a big effort to clean it all out for good, but one thing I'm stuck on is, how do I clean the railings out? Ofc I know to scrub in there and stuff, but they're so close to the ground, and the wastewater for that has to go somewhere. Is there a tool for handling this? Should I rent/buy a wet vac? Is my best options to just layer towels on the floor and wash them in vinegar afterwards? 😭

top 7 comments
sorted by: hot top controversial new old

Can you unmount them? That would make it much easier to clean behind them and from all sides (maybe even immerse in water). Then screw them back in place. I found my rail-guided shower doors so cumbersome to clean that I got rid of them altogether and replaced them with the simplest shower curtain. You can just throw that one in the washer.

[–] KulunkelBoom@lemmus.org 5 points 1 week ago* (last edited 1 week ago)

Spray them with a bleach/water solution. Let it sit and bleach the organisms - they'll literally fade away - if persistent spray again. rinse it down (hose?). Chlorine is an element - in that concentration it won't even be noticed.

[–] i_stole_ur_taco@lemmy.ca 5 points 1 week ago

I treat it like cleaning the trim around windows.

Spray a spray cleaner. Doesn’t have to drown it - just get every moldy surface wet. Bleach solution is great (don’t get it on you). Windex is pretty effective, too.

Let it sit for a few minutes to soften everything up, then get in there with cotton swabs and paper towels.

It seems daunting, but that first paper towel and swab are going to already remove like 80% of the filth, and the rest after that is just detail work for as long as you can stand it.

[–] bryndos@fedia.io 4 points 1 week ago

ok, in contrast to all the alkaline fanboys. i go acid, strongest vinegar you can find for mould.

It probably doesn’t matter if you go ph high or ph low though. Vinegar is more tolerable than bleach though, to me at least. just don’t mix them..

[–] Powderhorn@beehaw.org 2 points 1 week ago

I have always found the most success with a dollar-store bristle handbrush. As others have said, a bleach solution is going to be a good starting point. Turn on the vent and open the window when pouring it into the railings and -- I say this from experience -- if you aren't getting the desired results, do not add ammonia to speed things up.

But basically, yeah, you want an old towel around for incidental splashes, but aim the brush such that the gunk is going into the shower, not creating a new hassle. I find that two hours is more than sufficient, and with good ventilation and you not being in the washroom, it's a pretty harmless chemical that gets the job done even at full consumer strength. Adding water within reason retains the efficacy while making the whole affair a fair sight cheaper. Basically, it'll smell like an indoor pool.

[–] YourBestFriend@quokk.au 2 points 1 week ago

Bleach bleach bleach bleach.

[–] MJHill@piefed.world 2 points 1 week ago

Bleach and vinegar are sooooo old school. Get yourself some Mold Armor. This shit kills mold like nothing you’ve ever seen. Also, if you look closely you will see that the rails drain into the shower, so rinse lightly and everything should go down the drain.