Linux

5222 readers

134 users here now

A community for everything relating to the linux operating system

Also check out !linux_memes@programming.dev

Original icon base courtesy of lewing@isc.tamu.edu and The GIMP

founded 1 year ago

MODERATORS

Ategon@programming.dev

anzo@programming.dev

dwraf_of_ignorance@programming.dev

Hardware issue (lemmy.world)

submitted 3 months ago by cosmicrookie@lemmy.world to c/linux@programming.dev

9 comments fedilink hide all child comments

Today, i turned on my Mint pc and it wouldn't let me type in a passpowrd. Even the mouse was not reacting.

So i rebooted, got a massive text wall that mentioned something about not syncing

When i rebooted again, it wouldn't start up only a few rotations with the fans and then it restarts and repeats this loop

I assume that this is a hardware issue but what should i be looking into and how do i make the recovery as smooth as possible?

you are viewing a single comment's thread
view the rest of the comments

[–] schizo@forum.uncomfortable.business 7 points 3 months ago (2 children)

Would the error happen to be "Kernel panic - not syncing: Attempted to kill init!"?

I'd assume that you've either had your filesystem corrupt itself or had the storage device/controller fail. But, since you're making it that far, and I'm assuming this is a SSD, it's probably more likely it's corruption.

I'd start by booting to a USB stick and seeing if you can fsck the filesystem(s) on your drive.

[–] cosmicrookie@lemmy.world 4 points 3 months ago (1 children)

So.. it won't even boot at all now. Only rotates the fans a few times and shuts down. Could it be a powerfully issue

[–] schizo@forum.uncomfortable.business 5 points 3 months ago (1 children)

Oof. Sounds like a anything-could-be-bad scenario.

Assuming this is a desktop? I'd proabably start with the PSU, and go from there, yeah.

[–] cosmicrookie@lemmy.world 1 points 3 months ago

Ok thanks. The PSU is the newest part in this PC. Was replaced half a year ago for doing the exact same thing. Sounds like there may be something breaking the PSU somehow

[–] cosmicrookie@lemmy.world 1 points 3 months ago (1 children)

Yeah that might be it!

That said, im not making it that far any more. When booting up, the fans start rotating for a few seconds and then it shuts down. Then it will try again and just keep repeating the process of only rotating the fans again and again

I'll try to see if i can boot off an USB. Any good links that explain what fsck is and how it works?

[–] schizo@forum.uncomfortable.business 2 points 3 months ago* (last edited 3 months ago)

Sure.

This depends on the name of your block devices, but you'd probably want to do this in two runs: a test run, and then a real run to fix the problems.

You probably can determine the drive name via lsblk -o NAME,MODEL command. You're probably looking for a sda/sdb/sdc device, though NVME drives may be named something else. Using -o NAME,MODEL gives you a column with the name and the device model which should make identifying what you're after simpler. Probably there's only going to be two devices listed, though: the USB stick and your SSD.

You also want to identify the exact partition, ex. sda1, since that's what FSCK will want. You're probably going to need to do all the partitions on the drive.

To fsck I like doing a dry run to see what happens since sometimes it's going to do things that are.... not strictly ideal: (replace /dev/device with the actual device name and partition, ex. /dev/sda1)

fsck -N /dev/device

Assuming there's nothing catastrophic that shows up, then

fsck -y /dev/device

to actually run the fsck on the filesystem.

Couple of warnings: this COULD explode the data on your drive depending on what's broken, so if there's something you MUST have a copy of, try to get it first. Again, to be 100% clear: depending what's wrong you could lose every last byte of data on that drive.