would love indexing and numbers on my handle
or just go full Japan and incorporate a thermostat
this post was submitted on 20 Nov 2025
153 points (93.2% liked)
Showerthoughts
38224 readers
2103 users here now
A "Showerthought" is a simple term used to describe the thoughts that pop into your head while you're doing everyday things like taking a shower, driving, or just daydreaming. The most popular seem to be lighthearted clever little truths, hidden in daily life.
Here are some examples to inspire your own showerthoughts:
- Both “200” and “160” are 2 minutes in microwave math
- When you’re a kid, you don’t realize you’re also watching your mom and dad grow up.
- More dreams have been destroyed by alarm clocks than anything else
Rules
- All posts must be showerthoughts
- The entire showerthought must be in the title
- No politics
- If your topic is in a grey area, please phrase it to emphasize the fascinating aspects, not the dramatic aspects. You can do this by avoiding overly politicized terms such as "capitalism" and "communism". If you must make comparisons, you can say something is different without saying something is better/worse.
- A good place for politics is c/politicaldiscussion
- Posts must be original/unique
- Adhere to Lemmy's Code of Conduct and the TOS
If you made it this far, showerthoughts is accepting new mods. This community is generally tame so its not a lot of work, but having a few more mods would help reports get addressed a little sooner.
Whats it like to be a mod? Reports just show up as messages in your Lemmy inbox, and if a different mod has already addressed the report, the message goes away and you never worry about it.
founded 2 years ago
MODERATORS
We have mixer taps in our bathroom sinks and showers. Just lift the handle up and the temp is the same as it was last time you used it.
I bet it would not be hard to 3d print a little ring with a twisty arrow that you could use to "save" your last handle placement, kinda a neat idea.
There are! They’re called thermostatic faucets.
I'm amazed at the comments explaining incoming water temperature fluctuations and pressures....
No no, thermostatic tap/faucet mixes waters depending on the output temperature. Ignores all of the variables except the thermal mass (I guess reaction speed) of the thermostatic system.
I think they are normally like 10x the price of a standard mixer tap tho.
So, it's a budget choice
Yeah, and obviously if the 'hot' water isnt hot, there isn't anything it can do.
load more comments
(1 replies)
My kitchen faucet does this. It's a 2-axis lever. Y axis is the temperature adjustment, X axis is flow. As long as you leave it set to the same Y position when you turn it off and on, it'll be at the "last used combination".
Mine did this was well. If looks like a little stick on a ball
It's reasonably common for showers to have a mixing valve and a flow rate valve on separate handles. That accomplishes what you want. You just have to remember which is which and only use the flow rate valve to turn on and off.
More importantly, hot water circulation systems should be more common. It's the waiting for the cold water in the line to flush out that really makes setting temperature a hassle.
and when the hot water heater is two floors down and the pipe from there runs up unheated parts of the building, it takes a very long time to get even a hint of warmth out of the hot water faucets.
i've lived 3 minutes away from hot water for nearly thirty years now. it sucks. if i ever get money enough to own a house, or choose where i live with little regard to cost, it will have instant hot water (tankless water heaters).
hot water circulation systems should be more common
That just sounds like a waste of energy. Why not have the water heater right next to your shower, so that there's no wait? It's how it was set up in my parents home. Really enjoyed that setup, never had to wait for hot water.
Depending on your location the wasted water from letting the faucet run can be much more valuable than the energy needed to maintain a circ system, however install cost is high and the lines need to be entirely insulated so really, new construction works best. I wanted it on my house but I think it'd just drive costs way up, especially with a tankless as it'd be firing all the damn time.
I'm irritated by these half-measures. Just bathe in the hot water heater!
Actually, fuck yeah. My parents also have one of those bad boys:
It's really nice to bathe in!
As a kid, I saw an old movie with one of these in action. A dude and a lady were victims about to be eaten with the soup, and had to move around in it swishing the liquid and tipping the pot. Good stuff...
Because the kitchen isn't always wall to wall with the bathroom?
That's still confusing to me. My parents had the water heater tank in the bathroom, between the shower/bath and the sink. The kitchen sink had a separate small water heater.
It's really a question of whether you have electric heating or a furnace or district heating.
It's not common to have more than one heat exchanger for hot water if you have a furnace or district heating.
Electrical is much easier. You can just place them anywhere and they don't cost as much to install. However, electricity is usually more expensive than district heating.
I once had a place with the separate small water heater for kitchen. Could barely get the dishes done. I prefer having to wait a minute for the bathroom gigantic tank water to make it to the kitchen. Actually my system is way more complex, but that's irrelevant for this discussion. I have 3 big tanks, two of which are powered by wood (so usually cold unless it's cold outside and I make fires). By turning some valves on or off I can get water from different tanks to different faucets, though not all combinations are possible. Perks of a 40 year old house that grandpa later made more improvements on, lol
Most houses in the US have a single water heater, usually in the basement or utility room, with pipes running all through the house.
On demand recirculating works reasonably well but only for people who tolerate it. Push button, wait 3 min, water hot. It works for me but I know it’s way too much trouble for other people. It saves water and energy.
load more comments
(3 replies)
load more comments
(5 replies)
I thought a hot water circulator would be great, and it kind of is, but it comes with a drawback that I hadn’t considered. If you want cold water from the tap, to fill a glass of water at night for example, you have to wait for that just as long as you would have had to for the hot water before!
The solution to that is for a third return line to be run during a new build or remodel, but that's definitely not a weekend project for most homes.
My super basic faucet handles are exactly that…you twist it left-right to set temp and tilt it up-down for pressure from off to full. We just leave it rotated wherever we like it for temp and tilt up to turn on each time to the desired pressure. Our water pressure is always variable, so the amount tilted up varies, but the “rotational temp” almost never needs changing. There’s no fancy thermostatic valve in these like some shower have. There’s even those fancy kitchen sink faucets that remember everything and you just tap them with your hand and they automatically turn on/off to your settings of temp and pressure. I think they are called “touchless faucets”. Pretty sure even Ikea sells one.
I feel like sink handles like mine are super common, too. I’ve had similar ones in the states and in Europe…
Indeed :). That's what these are. 
Keep in mind that mixing the levels of hot and cold water isn't the only factor in the final temperature. It's also the actual temperature of the water in the pipes. Depending on where your pipes run, the cold water in the pipes may be warmer or cooler than the underground source of the water. The hot water may also have cooled more or less since leaving your hot water heater. Initial temperature may therefore be too hot or cold compared to where it ends after a period of use.
Ambient temperature in the room will also affect how hot you want the final temperature to be
You mean a (single handle) mixer tap?
view more: next ›